Study on the application of active balancing device to solve the vibration problem for the rotor with bending fault

The rotor with bending faults that occurrs on the rotating machinery usually vibrates seriously. This paper investigates to apply the active balancing device on a flexible rotor with bending faults to solve the vibration problem. Two problems are studied by finite element method firstly： Where the balance actuator is fixed on the shaft and how much the balancing capacity of the active balancing device is needed. The experiment is then carried out on the test rig, which consists of a flexible rotor with bending faults. The test results indicate that the bending rotor peak vibration response can be decreased from 550~m to 40~tm below by using the active balancing device. The peak vibration response decreases approximately by 93 %. The synchronous vibration due to the rotor bending faults can be controlled effectively by using ac- tive balancing device. The active balancing device is especially adapted to solve the problem caused by thermal distortion with time-variation and randomness, which is varied with working conditions, thus it has good practical value in practice.     

Anti-interference method for HF radars by transmitting phase-modulated chirps

Radio frequency interference （RFI） is a major problem in high-frequency （HF） radars. Conventional filtering-involved RFI suppression methods may introduce distortions to the target signals of interest and often demand extra hardware costs. In this paper, a novel method for RFI suppression by using linearly or randomly phase-modulated （PM） chirps is proposed, which enables independent analyses of the target signal and the RFI. Furthermore, the directions of arrival （DOA） of the interference are used as constraints to ensure a better DOA estimation of the target. The effectiveness of the method is demonstrated by numerical simulation results. The method can greatly improve the anti-interference capabilities of HF radars and is extremely applicable in the portable and low-cost radar systems.     

Subsumption Checking between Concept Queries in Different Ontologies Based on Mutual Instances

This paper proposes a checking method based on mutual instances and discusses three key problems in the method： how to deal with mistakes in the mutual instances and how to deal with too many or too few mutual instances. It provides the checking based on the weighted mutual instances considering fault tolerance, gives a way to partition the large-scale mutual instances, and proposes a process greatly reducing the manual annotation work to get more mutual instances. Intension annotation that improves the checking method is also discussed. The method is practical and effective to check subsumption relations between concept queries in different ontologies based on mutual instances.     

Incorporating Domain Knowledge into Data Mining Process： An Ontology Based Framework

0 IntroductionTeosda,yth meyan hya voerg daantiazbaatisoenss t hhaatv ec hmaonrgee t ahnadn glarrogwe cdoatnatibnaus--ously. One of the i mportant research issues is incrementalmining. Otherwise, various researchers have made sugges-tions that domain knowledge should be incorporated intoknowledge discovery ( KDD) process[1]. We focus on somesteps of the KDDprocess-those steps tying up with data min-ing,called a data mining (DM) process .Agrawalet al[2]showed an active data mining process ,…     

一种考虑杆件初始弯曲的非线性杆单元

在假定杆件初始弯曲为半波正弦曲线的基础上,提出考虑初始弯曲的非线性杆单元,推导了轴力与轴向变形的关系和轴向切线刚度的表达式,得到了初始弯曲对轴向刚度的影响系数.分析表明,初始弯曲影响与刚度比、初始弯曲幅值、轴力大小以及杆单元长度有关.结合某索拱结构工程实例,研究不同初始预应力取值下,杆件初始弯曲对结构非线性稳定性能的影响程度和影响规律,结果表明:杆件初始弯曲对结构屈曲前的整体刚度影响很小,但对结构的极限荷载与屈曲后性能影响较大;初始预应力取值的增加对结构的位移控制非常有效,但是对结构的刚度影响却很小;在不同初始预应力取值下,极限荷载随杆件初始弯曲变化的规律相似,并且都接近于线性.非线性杆单元能够广泛应用于桁架结构和网格结构的设计与分析,在考虑杆件初始弯曲后,将使结构的设计与分析更加合理、更加科学.     

厚管壁电容层析成像图像重建算法

探讨了适合厚管壁条件下的电容层析成像图像重建算法.针对厚管壁管道内几种不同流型,分别采用LBP算法、Landweber迭代算法和BP神经网络对8电极电容传感器进行成像重建计算.结果表明:在厚管壁情况下,LBP算法重建的图像质量很差;Landweber迭代算法在层流下的重建效果好于核心流和环状流;而BP神经网络算法可以有效重建管道内的介质分布,但对于没有训练到的任意流型,其重建效果不够理想.     

界面反应及界面张力对Sn-Zn-Bi焊料润湿性的影响

通过合金化的方式得到了Sn-Zn-Bi三元及Sn-Zn-Bi-Nd四元无铅焊料,采用润湿平衡法测量了其润湿力和润湿时间,并对润湿后的焊料/Cu界面组织进行了分析.结果表明:Bi元素不参与焊料/Cu界面的扩散反应,但能够通过吸附作用降低界面张力,从而提高焊料在Cu基底上的润湿力;Zn元素优先向焊料/Cu界面进行扩散形成Cu5Zn8金属间化合物,且扩散层随焊料中Zn含量的提高而增长,此时固-液界面张力方向发生改变,润湿力提高,但润湿时间延长;Nd元素的作用类似于Bi,既能提高焊料的润湿力,也能够缩短润湿时间,是一种改善Sn-Zn基焊料润湿性的有效元素.     

基于代理的网格作业全局自适应迁移

作业迁移是实现网格作业服务质量保证和系统高效能的重要方法,在分析了传统进程迁移技术的基础上,根据网格系统的特点,提出了一种基于代理的网格作业全局自适应迁移模型,通过设计网格作业全局自适应迁移对象选定原则、迁移时机确定机制和作业迁移信息监控管理,解决了网格环境下作业迁移的关键问题.试验结果以及在西北工业大学校园计算网格中的实际应用验证了模型的有效性.     

轧机主传动轴断裂事故分析

为分析某热轧厂R2轧机传动轴断裂的原因,对该轧机在典型工况下传动轴受力状况进行了现场试验研究,采用现代设计方法对传动轴进行分析,结果表明,平衡力产生的弯矩造成轴的应力集中而导致断裂。根据此结果对轴的结构进行了改进。     

快速介入性活检技术在纵隔疾病诊断中的应用

目的探讨B超引导下自制穿刺导向器快速介入性活检技术在纵隔疾病诊断中的临床应用价值。方法对36例经X线、CT或MRI证实有纵膈占位性病变且不能确诊的患者行自制B超穿刺导向器引导下的快速自动活检。结果36例患者全部穿刺成功,取材满意,取材阳性率100%。34例有明确的病理结果,病理阳性率94.4%。结论B超引导下自制穿刺导向器的快速介入性活检技术所取组织能够充分满足病理切片需要,病理确诊阳性率高,无严重并发症,能够为临床提供可靠的诊断治疗依据。